Representatives
Rep Portal
Wall and ceiling lightingThis very broad category covers almost every building, from residential houses, through apartments, shopping centers, stadiums and even churches. Few LED lighting manufacturers offer such a wide range of products for creating wall and ceiling lighting. LED extrusions with space for power supply are used in apartment buildings. In the design phase, it is worth considering a LED extrusion for drywall as LED lighting fixtures can fulfill the role of sconce lamps while LED extrusion with a round cross section can create suspended fixtures with appealing form. Extrusion used KOZEL.
pic. 1
KOZEL is a recessed LED extrusion with wide aluminum wings, which are covered with gypsum plaster after mounting the extrusion. The final effect is a clean line of light flush with the surface of the ceiling or wall.
pic. 2
The stately internal staircase required strong general-purpose lighting. Long lines of light surrounding each of the six floors of the office building turned out to be the perfect solution. Extrusions used: MOD-50, KOZEL
pic. 3
The stately internal staircase required strong general-purpose lighting. Long lines of light surrounding each of the six floors of the office building turned out to be the perfect solution. Extrusions used: MOD-50, KOZEL
pic. 4
The KOZEL recessed aluminum extrusion has a structure that allows it to be completely hidden and flush with the surface of drywall. You can see only the pure line of light.
pic. 5
KOZUS is a recessed LED extrusion with wide aluminum wings, which are covered with gypsum plaster after mounting the extrusion. The final effect is a clean line of light flush with the surface of the ceiling or wall.
pic. 6
KOZUS is a recessed LED extrusion with wide aluminum wings, which are covered with gypsum plaster after mounting the extrusion. The final effect is a clean line of light flush with the surface of the ceiling or wall.
pic. 7
The effect of a line of light recessed in the ceiling suits minimalist interiors. This effect can be obtained using the KOZUS-50 extrusion which accommodates up to four LED strips and serves as general-purpose lighting. Its wide wings get covered with gypsum plaster and then painted.
pic. 8
The KOZUS-CR extrusion creates a line of light where the ceiling meets the wall. It provides a modern decorative backlight of the entire wall. The extrusion is mounted in the gap between the wall and ceiling using mounting adhesive.
pic. 9
The narrow recessed LED extrusion KOZMA has a structure that allows it to be completely hidden and flush with the ceiling surface. You can see only a thin line of light.
pic. 10
To produce a line of light without time-consuming plastering and painting, you can use extrusions with a narrow flange covering the edges of the groove. For general-purpose lighting you can use the LARKO-50 extrusion with up to four LED strips.
pic. 11
Ideally, lighting should be mounted during finishing works, but it happens that holes must be cut in the already mounted, finished ceiling. For this purpose we recommend extrusions with wide flanges that will cover the unsightly edges of the cut drywall. The OPAC-30 LED extrusion for drywall is easy to fix in the groove, even a shallow one.
pic. 12
The main lighting in drywall does not have to be limited to one straight line. The LOKOM LED extrusion for drywall can be combined at right angles and 135 degrees. It gives completely new possibilities in creating lighting.
pic. 13
Some items should be properly lit to emphasize their uniqueness and beauty. It is good when the fixture itself remains hidden; therefore in this type of arrangement consider the LOKOM recessed LED extrusion. By inserting two LED strips you can obtain a strong light source.
pic. 14
While walls and ceilings are still under construction, you can use architectural extrusions from KLUŚ. The TEKNIK, TEKUS and LIPOD systems will enable you to create extravagant lighting. The LIPOD extrusion can be mounted in a number of ways: recessed (with TEKNIK, TEKUS), on the surface, with light direction adjustment and suspending the extrusion on wires or rods. LIPOD can be combined at 90 and 135 degrees.
pic. 15
LED fixtures are currently considered standard equipment for office and open space. KLUŚ offers a special line of LED extrusions for drywall and Armstrong ceilings. Extrusions used: TEKUS and LOKOM
pic. 16
Effective lighting constructions will be always eye-catching and make the interior look unique. Therefore, it is worth considering the LED extrusions for drywall in the design phase. The TPK-4 and OPK-4 extrusions can be easily combined into straight and segmented runs, and the lighting fixtures can go seamlessly from recessed to suspended or even be bent (OPK-4).
pic. 17
LED lighting fixtures can be successfully used as general-purpose lighting. TRIADA extrusions, equipped with three LED strips, are a strong source of light. Numerous mounting accessories will allow you to hang the extrusion at the right height. TRIADA can bend into gentle arcs and create independent, effective LED fixtures.
pic. 18
For simple, minimalistic lighting you can use the 3035-O LED ceiling extrusion. The advantage of its design is the ability to run wires inside its mounting extrusion and simplified replacement of LEDs.
pic. 19
Using the extensive range of mounting accessories, the LIPOD extrusion can be mounted on various surfaces (drywall, wood, sheet metal, concrete, etc.). Ready-made, proven solutions will shorten the mounting time.
pic. 20
LED extrusions with space for the power supply are often used to create modern sconce fixtures. Hiding the power supply, electronic components and electrical connections in the additional chamber of the fixture greatly simplifies the assembly and speeds up servicing of the fixture. Extrusion used: KIDES
pic. 21
